SNMP - Walk

Declaration

<AMSNMPWALKREQUEST HOST="text" NAME="text" COMMUNITY="text" REMOTEPORT="text" TIMEOUT="text" BROADCASTDELAY="text" OIDSTRINGNOTATION="yes/no" TIMETICKSTRINGNOTATION="yes/no" SNMPVERSION="options" RESULTDATASET="text">

Related Topics   

Description

Issues a WALK message to an SNMP agent in order to inspect a group of variables.  

IMPORTANT: To get the most out of Automate Desktop's SNMP activities, users should have a fundamental understanding of SNMP architecture and its major elements, such as Managers, Agents, MIBs, and PDUs.

Practical usage

Commonly used to get the value of a group of SNMP variables on an SNMP capable agent such as a router.

Parameters

General

Property Type Required Default Markup Description
Agent IP address Text Yes (Empty) HOST="xxx.xxx.xxx.xxx" The IP Address or hostname of the SNMP agent to communicate with.
Variable name Text Yes (Empty)
  • NAME="1.3.6.1.2.1.1.1.0"
  • NAME="system.sysDescr.0"
 The SNMP variable to set. This value can be an OID (Object Identifier) in either numeric or human-readable format.
NOTE: This is not an Automate Desktop variable.
Community Text Yes (Empty) COMMUNITY="NetAuto" The SNMP community name.
Create and populate dataset Text Yes (Empty) RESULTDATASET="myData" The name of the dataset to be created and populated with the results of the request.

Advanced

Property Type Required Default Markup Description
Timeout after Text Yes 30 TIMEOUT="30" The total elapsed time that this activity should wait for a response before generating a timeout error. The default is 30 seconds.
Timeout measure Text (options) Yes seconds
  • TIMEOUTMEASURE="milliseconds"
  • TIMEOUTMEASURE="seconds"
  • TIMEOUTMEASURE="minutes"
  • TIMEOUTMEASURE="hours"
 The time measurement that corresponds to the value entered in the Timeout after parameter. The available options are:
  • milliseconds - Timeout value will be measured in milliseconds.
  • seconds (default) - Timeout value will be measured in seconds.
  • minutes - Timeout value will be measured in minutes.
  • hours - Timeout value will be measured in hours.
Broadcast delay Number No 3 BROADCASTDELAY="10" The maximum broadcast delay time that this activity will allow. The default is 3 seconds.
Broadcast Measure Text (options) No seconds
  • BROADCASTMEASURE="milliseconds"
  • BROADCASTMEASURE="seconds"
  • BROADCASTMEASURE="minutes"
  • BROADCASTMEASURE="hours"
 The time measurement that corresponds to the broadcast delay value. The available options are:
  • milliseconds - Broadcast delay will be measured in milliseconds.
  • seconds (default) - Broadcast delay will be measured in seconds.
  • minutes - Broadcast delay will be measured in minutes.
  • hours - Broadcast delay will be measured in hours.
SNMP version Text (options) No SNMPv1
  • SNMPVERSION="SNMPv1"
  • SNMPVERSION="SNMPv2C"
  • SNMPVERSION="SNMPv3"
 The version of the SNMP protocol to use. The default is SNMP version 1 as it is the most prevalent. The available options are:
  • SNMPv1 (default)
  • SNMPv2c
  • SNMPv3
NOTE: SNMPv3 must be selected to enable the authentication protocol option.
Remote port Number No 161 REMOTEPORT="555" The TCP/IP port that should be used for the SNMP request. The default port is 161.
Authentication Protocol Text (options) No Do not use authentication
  • AUTHENTICATIONPROTOCOL="do not use authentication"
  • AUTHENTICATIONPROTOCOL="md5"
  • AUTHENTICATIONPROTOCOL="sha"
  • AUTHENTICATIONPROTOCOL="sha2"
 SNMPv3 must be selected to make this potion available. The available options for Authentication algorithm are:
  • Do not use authentication (default) - No authentication will be used.
  • MD5 (recommended) - MD5 authentication will be used.
  • SHA - SHA authentication will be used.
  • SHA2 - SHA2 authentication will be used.
Discovery time out Number Yes 30 seconds DISCOVERYTIMEOUT="30seconds" The total elapsed time that this activity should wait for a discovery before a time out.
Authentication username Text Yes empty USERNAME="username" User name to configure the remote user.
Privacy Algorithm Text (options) No Do not encrypt messages
  1. PRIVACYALGORITHM="do not encrypt messages"
  2. PRIVACYALGORITHM="des"
  3. PRIVACYALGORITHM="aes192"
  4. PRIVACYALGORITHM="aes256"
  5. PRIVACYALGORITHM="3des"
  6. PRIVACYALGORITHM="aes"

The available options for Privacy are:

  • Do not encrypt messages (default) - No encryption will be used.
  • DES (recommended) - DES encryption will be used.
  • AES192 - AES192 encryption will be used.
  • AES256 - AES256 encryption will be used.
  • 3DES - 3DES encryption will be used.
  • AES - AES encryption will be used.
Authentication password Text Yes Empty

PASSWORD="password"

 Password to configure the remote user.
Privacy password Text Yes Empty

PRIVACYPASSWORD="privacypassword'

 Privacy password for the algorithm.

Data

Property Type Required Default Markup Description
Use string notation for OIDs Yes/No No Yes OIDSTRINGNOTATION="no" Specifies whether the variable should contain the returning OID in numeric or "human readable" format. If selected, the value will be returned in human readable format. If disabled, the value will be returned in numeric format. This parameter is selected by default.
Use string notation for timetick values Yes/No Yes Yes TIMETICKSTRINGNOTATION="no" Timetick variable types are normally a 32-bit number but they can be returned in string notation. If this parameter is selected, the step will return the value in string notation. If disabled, this step will return the value in 32-bit number format. This parameter is selected by default.

Description

Error Causes

On Error

Example

NOTE:
  • Copy and paste the sample AML code below directly into the Task Builder Steps Panel.
  • To successfully run the sample code, update parameters containing user credentials, files, file paths, or other information specific to the task to match your environment.

Description

This sample task issues a SNMP Walk message to a SNMP agent in order to inspect a group of variables. This action can be used to get the value of a group of SNMP variables on an SNMP capable agent such as a router.

Copy 
<AMVARIABLE NAME="SNMPMessage" VALUE="" />
<AMSNMP ACTIVITY="walk" HOST="192.168.0.152" NAME="SNMPMessage" COMMUNITY="public" RESULTDATASET="theDataset" />
<AMLOOP ACTIVITY="dataset" DATASET="theDataset" />
<AMSHOWDIALOG>%SNMPMessage%</AMSHOWDIALOG>
<AMLOOP ACTIVITY="end" />